Nissan SR20DE Engine Essay Research Paper For

Nissan SR20DE Engine Essay, Research Paper

For those of you who want to upgrade your throttle body on your GA16DE powered

cars, there are a couple of options out there that you can do. You can have the

one on your bored out by a reputable machine shop (i.e. JG engine dynamics) or,

if you can get your hands on one, bolt on the throttle body from an SR20DE.

What’s the difference in the two you ask? Well I’ll tell you the advantages and

disadvantages in installing the two. The GA16DE’s throttle body’s anatomy

compared to the SR20DE throttle body is almost identical. The bolt patterns,

coolant hook-ups, and vacuum lines all match up the same. But the only

differences lie with the bore size, and the TPS configuration. With the 1.6

throttle body bored out to its maximum specifications, overall bore size will

still not be as large as the stock bore size of the 2.0 throttle body. Which

also leaves us to consider how much more potential there can be had with the 2.0

throttle body! If you can get your greasy hands on one of these throttle bodies,

I’ll let you guys know of some of the obstacles that will be encountered on

making this modification work. Necessary parts: There was not much needed here.

You will need to purchase brand new throttle body gasket from the dealership. It

only cost me about $4.50 with the Se-r discount at Puente Hills Nissan. Without

the discount its about six bucks. You will also need to make sure that it is for

an Se-r! Otherwise the bore size of the 1.6 gasket will not match the bore size

of the throttle body. You will also need to get an aftermarket intake setup, if

you don?t already have one. The factory rubber intake tubing will not fit over

the throttle body. If you have only the filter with the MAF adapter plate,

you’ll need to go out and get the mandrel bent intake pipe with the proper sized

couplers for the Se-r. You can also go out to Home Depot and make your own. If

you do that you’ll need some 2" abs pvc, 4 hose clamps and 2 2" rubber

couplers. The Home Depot couplers will be a very tight fit on the TB, but it

will fit. You’ll just need to stretch it over the mouth of the TB. I also went

out and bought a couple of brass fittings to tap into the side of the PVC for

the necessary vacuum hoses. These can be purchased at a Pep Boys autoparts store

for less than five bucks. Installation: Everything matched up perfectly, with a

few exceptions. There are two connections on the bottom of the TB for the

coolant hoses. You will have to slightly bend these so that they pint straight

down, otherwise they will be hitting against the manifold. I heated them up on

my gas kitchen stove, but if you have access to a butane torch then good for

you! Heat up the connections a little bit (NOT RED HOT!) , and use a shop hammer

to gently tap the tubing straight. You should be tapping the base of the body as

you are not trying to actually bend the tube, you just want it to rotate in its

base. The most challenging part of the throttle body mod will be with making the

1.6 TPS work on this unit. As I am still trying to figure out how to do this,

I’ll tell you what I have encountered so far. On the 2.0, the TPS lever sits

towards the front of the throttle body, rotating clockwise from the seven

o’clock position to eleven o’clock. On the 1.6 the TPS lever rotates clockwise

from the one o’clock position to about five o’clock. The same goes with the

lever on the TB that moves the TPS switch. One thing I tried to do was flip the

1.6 TPS around and bolt it backwards, with the plug end facing the intake

manifold. The levers made contact with each other to make the system operable,

but I was questioning its inability to then be unable to be adjusted. This set

up caused the TPS lever to be out of spec with its position slightly opened up,

even though the throttle was completely closed. Installation on the car was

slightly difficult as the TPS also got in the way of a few vacuum hoses and

rested against the intake manifold. Not good if you begin to wonder if the heat

would cook the plug in connector on the TPS. After starting up my car, I could

immediately hear the difference in sound. It actually sounds a lot healthier

with all the extra air going in the engine. Engine response was incredibly

awesome as the RPM’s just shoot to redline without any delay. The only bad part

was that the engine was idling way too high at about 2k. After taking a little

test drive around the block, the increased power was second to none, as I was

even able to get some 2nd gear peel out on my 16"s. Another bad part

though, after the initial run down the street, engine idle was now at 3-4k!! My

suspicions were of my poor, mis-calibrated TPS sensor. With the sensor mounted

backwards, adjustability was not going to be possible. That little fraction of

an inch that was needed to get the TPS sensor in the clo

Внимание, отключите Adblock

Вы посетили наш сайт со включенным блокировщиком рекламы!
Ссылка для скачивания станет доступной сразу после отключения Adblock!

Скачать